Dell POWERCONNECT 5324
Start the console session.
Plug in serial cable to console port of device from PC COM1 port
Open PuTTY and select "Serial" connection type, leave baud rate (Speed) and other settings as default.
Plug power into device and if a power button exists, turn it on.
Access Startup Menu.
Press Esc before the countdown ends:
BOOT Software Version 1.0.0.21 Built 10-Aug-2004 13:33:06 ## ########### ##### ###### ###### ############## ######### ###### ###### ############### ######### ###### ###### ################ ########## #### ###### ###### ################ ######### ###### ###### ###### ######################## ######### ###### ###### ###### ############## ######## ####### ###### ###### ###################### ######### ###### ###### #################### ########## ###### ###### ################### ########### ###### ###### ################## ############# ###### ###### ################################# ###### ################################################# ############ ################ ################ ############# ############ ################ ############## ############# ############ ############### ########## ############# ############ ############## ######## ############# ############ ########### #### ############# ############ ## PowerConnect 5324 board based on FireFox 88E6218 ARM946E-S processor 64 MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled. Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Bypass current configuration and boot.
When the Startup Menu appears, type 3 to ignore the current password, then press Enter to boot:
Startup Menu [1] Download Software [2] Erase Flash File [3] Password Recovery Procedure [4] Enter Diagnostic Mode [5] Set Terminal Baud-Rate [6] Back Enter your choice or press 'ESC' to exit: 3 Current password will be ignored! ==== Press Enter To Continue ==== Exit from boot menu. Continue with flow. Preparing to decompress... 100% Decompressing SW from image-1 1024000 OK Running from RAM... ********************************************************************* *** Running SW Ver. 1.0.0.45 Date 07-Jun-2004 Time 14:34:51 *** *********************************************************************
Further output will take you to the Dell Easy Setup Wizard.
Erase configuration and reboot.
When prompted to enter the setup wizard type n
Would you like to enter the setup wizard (you must answer this question within 60 seconds)? (Y/N)[Y] N
At the console> prompt type enable to access privileged mode:
console> enable
At the console# prompt type del startup-config and confirm with y:
console# del startup-config Delete startup-config [y/n]? y 01-Jan-2000 01:01:42 %FILE-I-DELETE: File Delete - file URL flash://startup- config Startup file was deleted
Type show vlan to see if any non-default vlans exist:
console# show vlan Vlan Name Ports Type Authorization ---- --------------- --------------------------- ------------ ------------- 1 1 ch(1-8) other Required 2 name2 g(4-10,12-13,16-17,19,22, permanent Required 24) 100 name100 g(1-9,24) permanent Required 300 name300 g(15,24) permanent Required 600 name600 g(4-9,14,18,20-21,23-24) permanent Required 602 name602 g(11,24) permanent Required 604 name604 g(4-9,24) permanent Required 666 name666 g(4-9,24) permanent Required
Delete non-default vlans:
console# configure console(config)# vlan database console(config-vlan)# no vlan 2 console(config-vlan)# no vlan 100 console(config-vlan)# no vlan 300 console(config-vlan)# no vlan 600 console(config-vlan)# no vlan 602 console(config-vlan)# no vlan 604 console(config-vlan)# no vlan 666 console(config-vlan)# exit console(config)# exit
Type the reload command and confirm with y until it does the system reset:
Console# reload You haven't saved your changes. Are you sure you want to continue ? (Y/N)[N] Y This command will reset the whole system and disconnect your current session. Do you want to continue ? (Y/N)[N] Y ************************************************** ***************** SYSTEM RESET ***************** **************************************************
Copy all the output from the session into your records.
Right-click PuTTY's titlebar, from that dropdown menu click on "Copy All to Clipboard"
Open the file of record certifying the deconfiguration of this device and use CTRL V to paste all the output from PuTTY into that file. Formatting the text with a fixed-width font helps it look more readable.
End the session.
Close PuTTy.