Cisco SGE2000 V01
Start the console session.
Plug in serial cable to console port of device from PC COM1 port
Open PuTTY and select "Serial" connection type, leave baud rate (Speed) and other settings as default.
Plug power into device and if a power button exists, turn it on.
Access Startup Menu
When prompted and before the countdown ends press the Esc key:
Boot1 Checksum Test...............................PASS Boot2 Checksum Test...............................PASS Flash Image Validation Test.......................PASS BOOT Software Version 2.0.0.03 Built 18-May-2009 11:44:56 Networking device with 88F5181 CPU based on ARM926EJ-S core. Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
This will present you with a numbered menu and an Enter your choice or press 'ESC' to exit: prompt.
Switch the working mode of the unit from stacking to standalone
At the Startup Menu prompt type 6 to access the Stack menu and press the Enter key:
Startup Menu [1] Download Software [2] Erase Flash File [3] Password Recovery Procedure [4] Enter Diagnostic Mode [5] Set Terminal Baud-Rate [6] Stack menu [7] Back Enter your choice or press 'ESC' to exit:6
At the Stack menu prompt type 3 to set the unit working mode, then type 1 to set it to standalone mode and press the Enter key.
Stack menu [1] Show unit stack id [2] Set unit stack id [3] Set unit working mode [4] Back Enter your choice or press 'ESC' to exit:3 Enter unit working mode [1 - standalone, 2 - stacking]: 1 Unit working mode changed to standalone. ==== Press Enter To Continue ====
Press the Esc key until you exit the boot menu:
Exit from boot menu. Continue with flow. Preparing to decompress... 100% Decompressing SW from image-1 100% OK Running from RAM... ******************************************************************** *** Running SW Ver. 3.0.2.0 Date 07-Nov-2011 Time 15:35:17 *** ******************************************************************** HW version is 00.00.01 Base Mac address is: f0:25:72:8a:a8:df Dram size is : 128M bytes Dram first block size is : 102400K bytes Dram first PTR is : 0x1800000 Dram second block size is : 4096K bytes Dram second PTR is : 0x7C00000 Flash size is: 16M 07-Nov-2011 15:35:21 %CDB-I-LOADCONFIG: Loading running configuration. 07-Nov-2011 15:35:21 %CDB-I-LOADCONFIG: Loading startup configuration. Device configuration: Slot 1 - SGE2000 HW Rev. 3 CPLD revision: 4 ------------------------------------ -- Unit Standalone -- ------------------------------------
Further output will bring you to the User Name: prompt.
Log in with default credentials and ensure configuration data has been erased.
Type cisco for both the User Name and Password, and type N when prompted to change the password:
>menu Login Screen ============ User Name: admin Password: admin
In the Switch Main Menu type 1 for the System Configuration Menu:
Switch Main Menu ================ 1. System Configuration Menu 2. Port Status 3. Port Configuration 4. System Mode 5. Help 0. Logout ArrowKey/TAB/BACK=Move SPACE=Toggle ENTER=Select ESC=Back
In the System Configuration Menu type 9 to Reset to Factory Defaults and confirm with the y key:
System Configuration Menu ========================= 1. System Information 2. Management Settings 3. Username & Password Settings 4. Security Settings 5. Vlan Management 6. IP Configuration 7. File Management 8. Restore System Default Settings 9. Reset to Factory Defaults 10. Reboot System 0. Back Are you sure? [Y/N]? y ArrowKey/TAB/BACK=Move SPACE=Toggle ENTER=Select ESC=Back
This will result in a system reset:
************************************************** ***************** SYSTEM RESET ***************** ************************************************** Boot1 Checksum Test...............................PASS Boot2 Checksum Test...............................PASS Flash Image Validation Test.......................PASS BOOT Software Version 2.0.0.03 Built 18-May-2009 11:44:56 Networking device with 88F5181 CPU based on ARM926EJ-S core.
Copy all the output from the session into your records.
Right-click PuTTY's titlebar, from that dropdown menu click on "Copy All to Clipboard"
Open the file of record certifying the deconfiguration of this device and use CTRL V to paste all the output from PuTTY into that file. Formatting the text with a fixed-width font helps it look more readable.
End the session.
Close PuTTy.