Adva FSP 3000R7 SH1HU-R/PF
Start the console session.
Plug in serial cable to console port of device from PC COM1 port
Open PuTTY and select "Serial" connection type, change baud rate (Speed) to 19200 and leave other settings as default.
Plug power into device and if a power button exists, turn it on.
Reset passwords.
Press the q key when you see the line "Autobooting in 3 seconds" before the countdown ends to access the => prompt:
U-Boot 1.2.0 (rev. 36 - Jan 24 2013 - 16:07:53) CPU: 8544_E, Version: 2.1, (0x803c0121) Core: E500, Version: 2.3, (0x80210023) Clocks: CPU: 799 MHz, CCB: 533 MHz, DDR: 266 MHz L1: D-cache 32 kB enabled, I-cache 32 kB enabled Board: NemiV3 PCB: 3 Assembly: 1 (2c0e) CA-ID: 3 LBC: 33 MHz DRAM: 2048 MB FLASH: 8 MB SRAM: 4 MB L2 cache 256KB: enabled FPGA: Revision: 8 ID: 6 In: serial Out: serial Err: serial Net: eTSEC1: PHY is generic PHY (221450) eTSEC1 IDE: Bus 0: OK Device 0: Model: SanDisk SDCFAA-004G Firm: HDX 7.07 Ser#: BNZ031314033321 Type: Removable Hard Disk Capacity: 3815.0 MB = 3.7 GB (7813120 x 512) Autobooting in 3 seconds =>
Type the setenv resetpasswords yes command followed by the saveenv command:
=> setenv resetpasswords yes => saveenv Saving Environment to EEPROM...
Type the reset command and allow the boot process to complete:
=> reset … ## Booting image at 00400000 ... Image Name: Linux-2.6.30.3 Created: 2013-05-15 14:05:24 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2384012 Bytes = 2.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Booting using flat device tree at 0x900040 …
Erase database.
Type admin for the login and CHGME.1A for the password:
FSP 3000R7 Rel.11.2.3 (Linux ppc 2.6.30.3) 22:00:31 @ ttyS1 lntnpmwx02gen login: admin Password: CHGME.1A
Use the arrow keys to navigate to the "System Management" submenu and press Enter, then navigate to "Software & Database Control" and press Enter:
- FSP3000-R7 Rel.11.2.3 + Service Overview + Service Management + Service Logging - System Management . System General Settings . System OSPF Settings . System IP Settings . Logical Interfaces . System Date & Time . SNMP Configuration . Software & Database Control + Profiles + Scheduled Actions + System Security Management + External Applications . Reboot NCU . Quit lntnpmwx01gen 2022-07-03 13:21:28 EST
Type 2 for the "Database" screen, then navigate using the arrow keys to "Reset to Factory Default" and press Enter:
+------------------------ Software & Database Control ------------------------+ || 1 RDISK SCUDISK | 2 Database | 3 NCU Update | 4 FWP Update | | |+-----------------+ +--------------------------------------------+| || ACT Database Version: 11-02-3 Created: 1970-02-02,22:47:09 || || File Name: F7011023.DBS || || Size Of File: 941056 Byte || || Comment: || || STBY Database Version: 11-02-3 Created: 1970-02-02,22:26:51 || || File Name: F7011023.DBS || || Size Of File: 941056 Byte || || Comment: || || RDISK File Name Size Created || || +----------------------------------------------------------+ || || | | || || | | || || | | || || +----------------------------------------------------------+ || || || || [ Cancel ] [Backup from ACT to RDISK] [Backup from ACT to SCUDISK] || || [Edit Comments] [Copy from RDISK to STBY] [Activate STBY] || || [Reset to Factory Default] || || || |+---------------------------------------------------------------------------+| lntnpmwx01gen --------------------------------- 2022-07-03 13:22:43 EST
Press enter on "OK" dialog to confirm:
+------------------------ Software & Database Control ------------------------+ || 1 RDISK SCUDISK | 2 Database | 3 NCU Update | 4 FWP Update | | |+-----------------+ +--------------------------------------------+| || +-----------------------------------------------------+7:09 || || | | || || | ACT Database Reset to Factory Defaults - initiated. | || || | Database should be Reset after reboot. | || || | |26:51 || || | [ OK ] | || || | | || || +-----------------------------------------------------+ || || RDISK File Name Size Created || || +----------------------------------------------------------+ || || | | || || | | || || | | || || +----------------------------------------------------------+ || || Operation in progress... || || [ Cancel ] [Backup from ACT to RDISK] [Backup from ACT to SCUDISK] || || [Edit Comments] [Copy from RDISK to STBY] [Activate STBY] || || [Reset to Factory Default] || || || |+---------------------------------------------------------------------------+| lntnpmwx01gen --------------------------------- 2022-07-03 13:24:08 EST
Ensure the "Comment" lines say "factory default database":
+------------------------ Software & Database Control ------------------------+ || 1 RDISK SCUDISK | 2 Database | 3 NCU Update | 4 FWP Update | | |+-----------------+ +--------------------------------------------+| || ACT Database Version: 11-02-3 Created: 2022-07-03,03:24:15 || || File Name: F7011023.DBS || || Size Of File: 941056 Byte || || Comment: RTF - factory default database || || STBY Database Version: 11-02-3 Created: 2022-07-03,03:28:23 || || File Name: F7011023.DBS || || Size Of File: 941056 Byte || || Comment: RTF - factory default database || || RDISK File Name Size Created || || +----------------------------------------------------------+ || || | | || || | | || || | | || || +----------------------------------------------------------+ || || Operation in progress... || || [ Cancel ] [Backup from ACT to RDISK] [Backup from ACT to SCUDISK] || || [Edit Comments] [Copy from RDISK to STBY] [Activate STBY] || || [Reset to Factory Default] || || || |+---------------------------------------------------------------------------+| ---------------------------------------------- 2022-07-03 03:28:27 GMT
Power cycle the device.
Unplug and replug in the power, allowing the device to boot up.
Copy all the output from the session into your records.
Right-click PuTTY's titlebar, from that dropdown menu click on "Copy All to Clipboard"
Open the file of record certifying the deconfiguration of this device and use CTRL V to paste all the output from PuTTY into that file. Formatting the text with a fixed-width font helps it look more readable.
End the session.
Close PuTTy.